Forum

Fltro Bridge UBNT

Postado por Rogerio em 7 de Maio de 2012 às 19:27

Passar so Trafego Pppoe na brid ubnt

Depois de muita pesquisa e varias tentativas consegui fazer com que so passe trafego pppoe.
-Primeiramente Configure o burlet,naano ou roquet como ap bridge.
-Faça o download do backup da configuraçao do ap ubnt.
-Abra o arquivo do backup com wordpad e acrescente essas linhas:

ebtables.4.cmd=-A FORWARD -p 0x8863 -j ACCEPT 
ebtables.4.status=enabled 
ebtables.5.cmd=-A FORWARD -p 0x8864 -j ACCEPT 
ebtables.5.status=enabled 
ebtables.6.cmd=-P FORWARD DROP 
ebtables.6.status=enabled 
ebtables.7.cmd=-A INPUT -p 0x0800 --in-interface ath0 -j DROP 
ebtables.7.status=enabled  
OBS:Lenbrando que perdera o acesso do ap pela interface wirelles so sendo possivel acessar pela eternet.
Com isso diminuira Drasticamente o trafego desnecessario.
O arquivo fica assim:
aaa.1.status=disabled 
aaa.status=disabled 
bridge.1.devname=br0 
bridge.1.fd=1 
bridge.1.port.1.devname=eth0 
bridge.1.port.1.status=enabled 
bridge.1.port.2.devname=ath0 
bridge.1.port.2.status=enabled 
bridge.1.port.3.devname=eth1 
bridge.1.port.3.status=enabled 
bridge.1.stp.status=disabled 
bridge.status=enabled 
dhcpc.1.devname=br0 
dhcpc.1.status=disabled 
dhcpc.status=disabled 
dhcpd.1.status=disabled 
dhcpd.status=disabled 
dnsmasq.1.devname=eth0 
dnsmasq.1.status=enabled 
dnsmasq.status=disabled 
ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT 
ebtables.1.status=disabled 
ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT 
ebtables.2.status=disabled 
ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP 
ebtables.3.status=disabled 
ebtables.4.cmd=-A FORWARD -p 0x8863 -j ACCEPT 
ebtables.4.status=enabled 
ebtables.5.cmd=-A FORWARD -p 0x8864 -j ACCEPT 
ebtables.5.status=enabled 
ebtables.6.cmd=-P FORWARD DROP 
ebtables.6.status=enabled 
ebtables.7.cmd=-A INPUT -p 0x0800 --in-interface ath0 -j DROP 
ebtables.7.status=enabled 
ebtables.50.status=disabled 
ebtables.51.status=disabled 
ebtables.52.status=disabled 
ebtables.status=enabled 
gui.language=pt_PT 
httpd.https.status=disabled 
httpd.port.http=80 
httpd.port=80 
httpd.status=enabled 
igmpproxy.status=disabled 
iptables.3.status=disabled 
iptables.status=disabled 
netconf.1.alias.1.status=disabled 
netconf.1.alias.2.status=disabled 
netconf.1.alias.3.status=disabled 
netconf.1.alias.4.status=disabled 
netconf.1.alias.5.status=disabled 
netconf.1.alias.6.status=disabled 
netconf.1.alias.7.status=disabled 
netconf.1.alias.8.status=disabled 
netconf.1.devname=eth0 
netconf.1.ip=0.0.0.0 
netconf.1.netmask=255.255.255.0 
netconf.1.promisc=enabled 
netconf.1.status=enabled 
netconf.1.up=enabled 
netconf.2.alias.1.status=disabled 
netconf.2.alias.2.status=disabled 
netconf.2.alias.3.status=disabled 
netconf.2.alias.4.status=disabled 
netconf.2.alias.5.status=disabled 
netconf.2.alias.6.status=disabled 
netconf.2.alias.7.status=disabled 
netconf.2.alias.8.status=disabled 
netconf.2.allmulti=enabled 
netconf.2.devname=ath0 
netconf.2.ip=0.0.0.0 
netconf.2.netmask=255.255.255.0 
netconf.2.promisc=enabled 
netconf.2.status=enabled 
netconf.2.up=enabled 
netconf.3.autoip.status=disabled 
netconf.3.devname=br0 
netconf.3.ip=192.168.1.20 
netconf.3.netmask=255.255.255.0 
netconf.3.status=enabled 
netconf.3.up=enabled 
netconf.status=enabled 
netmode=bridge 
ntpclient.status=disabled 
ppp.1.password= 
 ppp.1.status=disabled 
ppp.status=disabled 
pwdog.status=disabled 
radio.1.ack.auto=enabled 
radio.1.ackdistance=600 
radio.1.acktimeout=25 
radio.1.ampdu.bytes=50000 
radio.1.ampdu.frames=32 
radio.1.ampdu.status=enabled 
radio.1.chanshift=0 
radio.1.clksel=1 
radio.1.countrycode=840 
radio.1.cwm.enable=0 
radio.1.cwm.mode=2 
radio.1.devname=ath0 
radio.1.dfs.status= 
 radio.1.forbiasauto=1 
radio.1.frag=off 
radio.1.freq=2412 
radio.1.ieee_mode=11nght40plus 
radio.1.mcastrate= 
 radio.1.mode=master 
radio.1.polling=disabled 
radio.1.rate.auto=enabled 
radio.1.rate.mcs=auto 
radio.1.rts=off 
radio.1.status=enabled 
radio.1.subsystemid=0xe202 
radio.1.thresh62a= 
 radio.1.thresh62b= 
 radio.1.thresh62g= 
 radio.1.txpower=10 
radio.countrycode=840 
radio.status=enabled 
resolv.host.1.name=UBNT 
resolv.host.1.status=enabled 
resolv.nameserver.1.ip=0.0.0.0 
resolv.nameserver.1.status=enabled 
resolv.nameserver.2.status=disabled 
resolv.status=enabled 
route.1.devname=br0 
route.1.gateway=192.168.1.20 
route.1.ip=0.0.0.0 
route.1.netmask=0 
route.1.status=enabled 
route.status=enabled 
snmp.status=disabled 
sshd.port=22 
sshd.status=disabled 
syslog.remote.status= 
 syslog.status=disabled 
telnetd.status=disabled 
tshaper.status=disabled 
users.1.name=ubnt 
users.1.password=VvpvCwhccFv6Q 
users.1.status=enabled 
users.2.status=disabled 
users.status=enabled 
wireless.1.addmtikie=disabled 
wireless.1.ap= 
 wireless.1.authmode=1 
wireless.1.compression=0 
wireless.1.devname=ath0 
wireless.1.fastframes=0 
wireless.1.frameburst=0 
wireless.1.hide_ssid=disabled 
wireless.1.l2_isolation=enabled 
wireless.1.mac_acl.1.mac= 
 wireless.1.mac_acl.1.status=disabled 
wireless.1.mac_acl.10.mac= 
 wireless.1.mac_acl.10.status=disabled 
wireless.1.mac_acl.11.mac= 
 wireless.1.mac_acl.11.status=disabled 
wireless.1.mac_acl.12.mac= 
 wireless.1.mac_acl.12.status=disabled 
wireless.1.mac_acl.13.mac= 
 wireless.1.mac_acl.13.status=disabled 
wireless.1.mac_acl.14.mac= 
 wireless.1.mac_acl.14.status=disabled 
wireless.1.mac_acl.15.mac= 
 wireless.1.mac_acl.15.status=disabled 
wireless.1.mac_acl.16.mac= 
 wireless.1.mac_acl.16.status=disabled 
wireless.1.mac_acl.2.mac= 
 wireless.1.mac_acl.2.status=disabled 
wireless.1.mac_acl.3.mac= 
 wireless.1.mac_acl.3.status=disabled 
wireless.1.mac_acl.4.mac= 
 wireless.1.mac_acl.4.status=disabled 
wireless.1.mac_acl.5.mac= 
 wireless.1.mac_acl.5.status=disabled 
wireless.1.mac_acl.6.mac= 
 wireless.1.mac_acl.6.status=disabled 
wireless.1.mac_acl.7.mac= 
 wireless.1.mac_acl.7.status=disabled 
wireless.1.mac_acl.8.mac= 
 wireless.1.mac_acl.8.status=disabled 
wireless.1.mac_acl.9.mac= 
 wireless.1.mac_acl.9.status=disabled 
wireless.1.mac_acl.policy=allow 
wireless.1.mac_acl.status=disabled 
wireless.1.macclone=disabled 
wireless.1.security=none 
wireless.1.signal_led1=94 
wireless.1.signal_led2=80 
wireless.1.signal_led3=73 
wireless.1.signal_led4=65 
wireless.1.ssid=ubnt 
wireless.1.status=enabled 
wireless.1.wds=disabled 
wireless.1.wmm=enabled 
wireless.1.wmmlevel= 
 wireless.status=enabled 
wpasupplicant.device.1.status=disabled 
wpasupplicant.status=disabled  

Depois salve e upa devolta para o ap ubnt.
FAçan o teste e vejan que melhora e muito 
Para versoes 5.5.x
ebtables.5.comment=Drop IPV6
ebtables.5.cmd=-A FIREWALL -i eth0 -p 0x86DD -j DROP
ebtables.5.status=enabled
ebtables.4.comment=Drop IPV4
ebtables.4.cmd=-A FIREWALL -i eth0 -p 0x0800 -j DROP
ebtables.4.status=enabled
ebtables.3.comment=
ebtables.3.cmd=-P FORWARD DROP 
ebtables.3.status=enabled
ebtables.2.comment=PPPoE Discovery Stage
ebtables.2.cmd=-A FORWARD -p 0x8864 -j ACCEPT 
ebtables.2.status=enabled
ebtables.1.comment=PPPoE Session Stage
ebtables.1.cmd=-A FORWARD -p 0x8863 -j ACCEPT 
ebtables.1.status=enabled
Lenbrando que esse ultimo tem> que abilitar o firewall
creditos Leonardo Silva
Visualizações: 30

Para adicionar comentários, você deve ser membro de MK-AUTH.

Join MK-AUTH

Marcações: mudar, pppoe, somente, trafego
★
★
★
★
★
Votos 0
Enviar-me um email quando as pessoas responderem –
Seguir

Respostas

  • Leonardo Silva Mendes Novembro 30, 2012 15:13

    boa tarde turma. seguinte não sei porque mas na versão 5.5.2 não estava bloqueando acesso  então eu fiz uma modificação que aparentemente deu certo abaixo segue exemplo

    ebtables.5.comment=Drop IPV6
    ebtables.5.cmd=-A FIREWALL -i eth0 -p 0x86DD -j DROP
    ebtables.5.status=enabled
    ebtables.4.comment=Drop IPV4
    ebtables.4.cmd=-A FIREWALL -i eth0 -p 0x0800 -j DROP
    ebtables.4.status=enabled
    ebtables.3.comment=
    ebtables.3.cmd=-P FORWARD DROP
    ebtables.3.status=enabled
    ebtables.2.comment=PPPoE Discovery Stage
    ebtables.2.cmd=-A FORWARD -p 0x8864 -j ACCEPT
    ebtables.2.status=enabled
    ebtables.1.comment=PPPoE Session Stage
    ebtables.1.cmd=-A FORWARD -p 0x8863 -j ACCEPT
    ebtables.1.status=enabled

    ps o firewall na aba network deve estar habilitado para funcionar . alem disto como podem ver eu fiz um drop no protocolo 0x86DD que de acordo com a Wikipedia é o código ethertype para ipv6 (ja habilitado por padrão no windows vista em diante se não me engano) outra coisa que pude perceber é que o drop é feito na ether0 e aparentemente será necessário fazer na ether1 também no caso das nanos com duas portas. alem disto o cliente perde acesso ao equipamento, mas você via wireless não. se possível testem e postem o resultado

  • AUGUSTO Novembro 13, 2012 21:44

    Boa Noite.

    com essa regra mencionada eu consigo bloquear tudo menos PPPoE e acesso aos radios?

  • francisco crystian horta de souz Novembro 11, 2012 0:34

    oi amigo..

    ja conseguiu fazer funcionar na versão 5.5.2

  • Rogerio Outubro 24, 2012 9:23

    Ta no lugar certo vou fazer um teste aki

  • francisco crystian horta de souz Outubro 24, 2012 8:29

    quando coloquei a 5.5.2 eu não deu certo pois continuo tendo acesso ao radio via wireless.. sera que tou colocando a regra no lugar errado..tem como vc da uma olhadinha grato

    aaa.1.br.devname=br0
    aaa.1.devname=ath0
    aaa.1.driver=madwifi
    aaa.1.radius.acct.1.status=disabled
    aaa.1.radius.auth.1.status=disabled
    aaa.1.radius.macacl.status=disabled
    aaa.1.ssid= tecnetsolardasgaivotas
    aaa.1.status=disabled
    aaa.1.wpa.1.pairwise=TKIP
    aaa.1.wpa.key.1.mgmt=WPA-PSK
    aaa.1.wpa.mode=2
    aaa.1.wpa.psk= kwqrt67843loanh3251O
    aaa.status=disabled
    bridge.1.devname=br0
    bridge.1.fd=1
    bridge.1.port.1.devname=eth0
    bridge.1.port.1.prio=10
    bridge.1.port.1.status=enabled
    bridge.1.port.2.devname=ath0
    bridge.1.port.2.prio=30
    bridge.1.port.2.status=enabled
    bridge.1.status=enabled
    bridge.1.stp.status=disabled
    bridge.status=enabled
    dhcpc.1.devname=br0
    dhcpc.1.status=disabled
    dhcpc.status=disabled
    dhcpd.status=disabled
    discovery.status=enabled
    dnsmasq.1.devname=eth0
    dnsmasq.1.status=enabled
    dnsmasq.status=disabled
    dyndns.status=disabled
    ebtables.status=enabled
    ebtables.sys.arpnat.1.devname=ath0
    ebtables.sys.arpnat.1.status=enabled
    ebtables.sys.arpnat.status=disabled
    ebtables.sys.eap.status=disabled
    ebtables.sys.status=enabled
    ebtables.sys.vlan.status=disabled
    ebtables.4.cmd=-A FORWARD -p 0x8863 -j ACCEPT
    ebtables.4.status=enabled
    ebtables.5.cmd=-A FORWARD -p 0x8864 -j ACCEPT
    ebtables.5.status=enabled
    ebtables.6.cmd=-P FORWARD DROP
    ebtables.6.status=enabled
    ebtables.7.cmd=-A INPUT -p 0x0800 --in-interface ath0 -j DROP
    ebtables.7.status=enabled
    gui.language=pt_PT
    httpd.https.status=disabled
    httpd.port=6622
    httpd.session.timeout=900
    httpd.status=enabled
    igmpproxy.status=disabled
    iptables.status=disabled
    netconf.1.autoip.status=disabled
    netconf.1.autoneg=enabled
    netconf.1.devname=eth0
    netconf.1.duplex=enabled
    netconf.1.hwaddr.mac=
    netconf.1.hwaddr.status=disabled
    netconf.1.ip=0.0.0.0
    netconf.1.mtu=1500
    netconf.1.netmask=255.255.255.0
    netconf.1.promisc=enabled
    netconf.1.role=bridge_port
    netconf.1.speed=100
    netconf.1.status=enabled
    netconf.1.up=enabled
    netconf.2.allmulti=disabled
    netconf.2.autoip.status=disabled
    netconf.2.devname=ath0
    netconf.2.hwaddr.mac=
    netconf.2.hwaddr.status=disabled
    netconf.2.ip=0.0.0.0
    netconf.2.mtu=1500
    netconf.2.netmask=255.255.255.0
    netconf.2.promisc=enabled
    netconf.2.role=bridge_port
    netconf.2.status=enabled
    netconf.2.up=enabled
    netconf.3.autoip.status=enabled
    netconf.3.devname=br0
    netconf.3.hwaddr.mac=
    netconf.3.hwaddr.status=disabled
    netconf.3.ip=192.168.60.44
    netconf.3.mtu=1500
    netconf.3.netmask=255.255.255.0
    netconf.3.role=mlan
    netconf.3.status=enabled
    netconf.3.up=enabled
    netconf.status=enabled
    netmode=bridge
    ntpclient.status=disabled
    ppp.status=disabled
    pwdog.status=disabled
    radio.1.ack.auto=enabled
    radio.1.ackdistance=1500
    radio.1.acktimeout=31
    radio.1.ampdu.bytes=50000
    radio.1.ampdu.frames=32
    radio.1.ampdu.status=enabled
    radio.1.antenna.gain=17
    radio.1.antenna.id=
    radio.1.cable.loss=0
    radio.1.chanbw=0
    radio.1.chanshift=5
    radio.1.clksel=1
    radio.1.countrycode=511
    radio.1.cwm.enable=0
    radio.1.cwm.mode=0
    radio.1.devname=ath0
    radio.1.dfs.status=disabled
    radio.1.forbiasauto=0
    radio.1.freq=5405
    radio.1.ieee_mode=11naht20
    radio.1.low_txpower_mode=disabled
    radio.1.mcastrate=15
    radio.1.mode=master
    radio.1.obey=disabled
    radio.1.polling=enabled
    radio.1.pollingnoack=0
    radio.1.pollingpri=
    radio.1.rate.auto=disabled
    radio.1.rate.mcs=4
    radio.1.reg_obey=disabled
    radio.1.rts=off
    radio.1.status=enabled
    radio.1.subsystemid=0xe1b5
    radio.1.thresh62a=
    radio.1.thresh62b=
    radio.1.thresh62g=
    radio.1.txpower=24
    radio.countrycode=511
    radio.status=enabled
    resolv.host.1.name=transmisor charles1
    resolv.host.1.status=enabled
    resolv.nameserver.1.ip=
    resolv.nameserver.1.status=disabled
    resolv.nameserver.2.ip=
    resolv.nameserver.2.status=disabled
    resolv.nameserver.status=enabled
    resolv.status=enabled
    route.1.comment=
    route.1.devname=br0
    route.1.gateway=192.168.1.1
    route.1.ip=0.0.0.0
    route.1.netmask=0
    route.1.status=enabled
    route.status=enabled
    snmp.status=disabled
    sshd.auth.passwd=enabled
    sshd.port=8888
    sshd.status=enabled
    syslog.remote.status=
    syslog.status=disabled
    system.button.reset=enabled
    system.cfg.version=65540
    system.date.status=disabled
    system.date.timestamp=
    system.eirp.status=enabled
    system.latitude=
    system.longitude=
    system.timezone=GMT
    telnetd.status=disabled
    tshaper.1.devname=ath0
    tshaper.1.input.burst=0
    tshaper.1.input.cburst=0
    tshaper.1.input.rate=512
    tshaper.1.input.status=enabled
    tshaper.1.output.burst=0
    tshaper.1.output.cburst=0
    tshaper.1.output.rate=512
    tshaper.1.output.status=enabled
    tshaper.1.status=enabled
    tshaper.2.devname=eth0
    tshaper.2.input.burst=0
    tshaper.2.input.cburst=0
    tshaper.2.input.rate=512
    tshaper.2.input.status=enabled
    tshaper.2.output.burst=0
    tshaper.2.output.cburst=0
    tshaper.2.output.rate=512
    tshaper.2.output.status=enabled
    tshaper.2.status=enabled
    tshaper.status=disabled
    update.check.status=disabled
    users.1.name=xcharlesx
    users.1.password=DdNOEtKJhg69g
    users.1.status=enabled
    users.2.status=disabled
    users.status=enabled
    vlan.status=disabled
    wireless.1.addmtikie=disabled
    wireless.1.ap=
    wireless.1.authmode=1
    wireless.1.autowds=disabled
    wireless.1.compression=0
    wireless.1.devname=ath0
    wireless.1.fastframes=0
    wireless.1.frameburst=0
    wireless.1.hide_ssid=enabled
    wireless.1.l2_isolation=disabled
    wireless.1.mac_acl.1.comment=
    wireless.1.mac_acl.1.mac=00:27:22:B6:7E:1A
    wireless.1.mac_acl.1.status=enabled
    wireless.1.mac_acl.2.comment=
    wireless.1.mac_acl.2.mac=00:27:22:B6:75:18
    wireless.1.mac_acl.2.status=enabled
    wireless.1.mac_acl.policy=allow
    wireless.1.mac_acl.status=disabled
    wireless.1.macclone=disabled
    wireless.1.mcast.enhance=0
    wireless.1.scan_list.channels=5405
    wireless.1.scan_list.status=enabled
    wireless.1.security.type=none
    wireless.1.sens=0
    wireless.1.signal_led1=94
    wireless.1.signal_led2=80
    wireless.1.signal_led3=73
    wireless.1.signal_led4=65
    wireless.1.signal_led_status=enabled
    wireless.1.ssid=  tecnet 1O charles1  
    wireless.1.status=enabled
    wireless.1.wds.1.peer=
    wireless.1.wds.2.peer=
    wireless.1.wds.3.peer=
    wireless.1.wds.4.peer=
    wireless.1.wds.5.peer=
    wireless.1.wds.6.peer=
    wireless.1.wds.status=enabled
    wireless.1.wmm=enabled
    wireless.1.wmmlevel=
    wireless.status=enabled
    wpasupplicant.device.1.status=disabled
    wpasupplicant.profile.1.network.1.psk= kwqrt67843loanh3251O
    wpasupplicant.status=disabled

  • Rogerio Outubro 23, 2012 22:22

    Use uma fonte q tenha o botão de reset mas se vc deixou a pcao de reset desativada  ai nao sei o q faxer

  • Orlando Barbosa da Silva Outubro 23, 2012 20:01

    amigo sei que não tem anda aver com o seu post mais vc sabe como reseta a nanobrideg m5 pois vejo o botão de resetar e no poe tbm não tem e eu não sei a senha

  • francisco crystian horta de souz Outubro 23, 2012 19:06

    na 5.5.2 fica eu coloquei e fiquei tendo acesso ao radio..de uma olhada

    aaa.1.br.devname=br0
    aaa.1.devname=ath0
    aaa.1.driver=madwifi
    aaa.1.radius.acct.1.status=disabled
    aaa.1.radius.auth.1.status=disabled
    aaa.1.radius.macacl.status=disabled
    aaa.1.ssid= tecnetsolardasgaivotas
    aaa.1.status=disabled
    aaa.1.wpa.1.pairwise=TKIP
    aaa.1.wpa.key.1.mgmt=WPA-PSK
    aaa.1.wpa.mode=2
    aaa.1.wpa.psk= kwqrt67843loanh3251O
    aaa.status=disabled
    bridge.1.devname=br0
    bridge.1.fd=1
    bridge.1.port.1.devname=eth0
    bridge.1.port.1.prio=10
    bridge.1.port.1.status=enabled
    bridge.1.port.2.devname=ath0
    bridge.1.port.2.prio=30
    bridge.1.port.2.status=enabled
    bridge.1.status=enabled
    bridge.1.stp.status=disabled
    bridge.status=enabled
    dhcpc.1.devname=br0
    dhcpc.1.status=disabled
    dhcpc.status=disabled
    dhcpd.status=disabled
    discovery.status=enabled
    dnsmasq.1.devname=eth0
    dnsmasq.1.status=enabled
    dnsmasq.status=disabled
    dyndns.status=disabled
    ebtables.status=enabled
    ebtables.sys.arpnat.1.devname=ath0
    ebtables.sys.arpnat.1.status=enabled
    ebtables.sys.arpnat.status=disabled
    ebtables.sys.eap.status=disabled
    ebtables.sys.status=enabled
    ebtables.sys.vlan.status=disabled
    ebtables.4.cmd=-A FORWARD -p 0x8863 -j ACCEPT
    ebtables.4.status=enabled
    ebtables.5.cmd=-A FORWARD -p 0x8864 -j ACCEPT
    ebtables.5.status=enabled
    ebtables.6.cmd=-P FORWARD DROP
    ebtables.6.status=enabled
    ebtables.7.cmd=-A INPUT -p 0x0800 --in-interface ath0 -j DROP
    ebtables.7.status=enabled
    gui.language=pt_PT
    httpd.https.status=disabled
    httpd.port=6622
    httpd.session.timeout=900
    httpd.status=enabled
    igmpproxy.status=disabled
    iptables.status=disabled
    netconf.1.autoip.status=disabled
    netconf.1.autoneg=enabled
    netconf.1.devname=eth0
    netconf.1.duplex=enabled
    netconf.1.hwaddr.mac=
    netconf.1.hwaddr.status=disabled
    netconf.1.ip=0.0.0.0
    netconf.1.mtu=1500
    netconf.1.netmask=255.255.255.0
    netconf.1.promisc=enabled
    netconf.1.role=bridge_port
    netconf.1.speed=100
    netconf.1.status=enabled
    netconf.1.up=enabled
    netconf.2.allmulti=disabled
    netconf.2.autoip.status=disabled
    netconf.2.devname=ath0
    netconf.2.hwaddr.mac=
    netconf.2.hwaddr.status=disabled
    netconf.2.ip=0.0.0.0
    netconf.2.mtu=1500
    netconf.2.netmask=255.255.255.0
    netconf.2.promisc=enabled
    netconf.2.role=bridge_port
    netconf.2.status=enabled
    netconf.2.up=enabled
    netconf.3.autoip.status=enabled
    netconf.3.devname=br0
    netconf.3.hwaddr.mac=
    netconf.3.hwaddr.status=disabled
    netconf.3.ip=192.168.60.44
    netconf.3.mtu=1500
    netconf.3.netmask=255.255.255.0
    netconf.3.role=mlan
    netconf.3.status=enabled
    netconf.3.up=enabled
    netconf.status=enabled
    netmode=bridge
    ntpclient.status=disabled
    ppp.status=disabled
    pwdog.status=disabled
    radio.1.ack.auto=enabled
    radio.1.ackdistance=1500
    radio.1.acktimeout=31
    radio.1.ampdu.bytes=50000
    radio.1.ampdu.frames=32
    radio.1.ampdu.status=enabled
    radio.1.antenna.gain=17
    radio.1.antenna.id=
    radio.1.cable.loss=0
    radio.1.chanbw=0
    radio.1.chanshift=5
    radio.1.clksel=1
    radio.1.countrycode=511
    radio.1.cwm.enable=0
    radio.1.cwm.mode=0
    radio.1.devname=ath0
    radio.1.dfs.status=disabled
    radio.1.forbiasauto=0
    radio.1.freq=5405
    radio.1.ieee_mode=11naht20
    radio.1.low_txpower_mode=disabled
    radio.1.mcastrate=15
    radio.1.mode=master
    radio.1.obey=disabled
    radio.1.polling=enabled
    radio.1.pollingnoack=0
    radio.1.pollingpri=
    radio.1.rate.auto=disabled
    radio.1.rate.mcs=4
    radio.1.reg_obey=disabled
    radio.1.rts=off
    radio.1.status=enabled
    radio.1.subsystemid=0xe1b5
    radio.1.thresh62a=
    radio.1.thresh62b=
    radio.1.thresh62g=
    radio.1.txpower=24
    radio.countrycode=511
    radio.status=enabled
    resolv.host.1.name=transmisor charles1
    resolv.host.1.status=enabled
    resolv.nameserver.1.ip=
    resolv.nameserver.1.status=disabled
    resolv.nameserver.2.ip=
    resolv.nameserver.2.status=disabled
    resolv.nameserver.status=enabled
    resolv.status=enabled
    route.1.comment=
    route.1.devname=br0
    route.1.gateway=192.168.1.1
    route.1.ip=0.0.0.0
    route.1.netmask=0
    route.1.status=enabled
    route.status=enabled
    snmp.status=disabled
    sshd.auth.passwd=enabled
    sshd.port=8888
    sshd.status=enabled
    syslog.remote.status=
    syslog.status=disabled
    system.button.reset=enabled
    system.cfg.version=65540
    system.date.status=disabled
    system.date.timestamp=
    system.eirp.status=enabled
    system.latitude=
    system.longitude=
    system.timezone=GMT
    telnetd.status=disabled
    tshaper.1.devname=ath0
    tshaper.1.input.burst=0
    tshaper.1.input.cburst=0
    tshaper.1.input.rate=512
    tshaper.1.input.status=enabled
    tshaper.1.output.burst=0
    tshaper.1.output.cburst=0
    tshaper.1.output.rate=512
    tshaper.1.output.status=enabled
    tshaper.1.status=enabled
    tshaper.2.devname=eth0
    tshaper.2.input.burst=0
    tshaper.2.input.cburst=0
    tshaper.2.input.rate=512
    tshaper.2.input.status=enabled
    tshaper.2.output.burst=0
    tshaper.2.output.cburst=0
    tshaper.2.output.rate=512
    tshaper.2.output.status=enabled
    tshaper.2.status=enabled
    tshaper.status=disabled
    update.check.status=disabled
    users.1.name=xcharlesx
    users.1.password=DdNOEtKJhg69g
    users.1.status=enabled
    users.2.status=disabled
    users.status=enabled
    vlan.status=disabled
    wireless.1.addmtikie=disabled
    wireless.1.ap=
    wireless.1.authmode=1
    wireless.1.autowds=disabled
    wireless.1.compression=0
    wireless.1.devname=ath0
    wireless.1.fastframes=0
    wireless.1.frameburst=0
    wireless.1.hide_ssid=enabled
    wireless.1.l2_isolation=disabled
    wireless.1.mac_acl.1.comment=
    wireless.1.mac_acl.1.mac=00:27:22:B6:7E:1A
    wireless.1.mac_acl.1.status=enabled
    wireless.1.mac_acl.2.comment=
    wireless.1.mac_acl.2.mac=00:27:22:B6:75:18
    wireless.1.mac_acl.2.status=enabled
    wireless.1.mac_acl.policy=allow
    wireless.1.mac_acl.status=disabled
    wireless.1.macclone=disabled
    wireless.1.mcast.enhance=0
    wireless.1.scan_list.channels=5405
    wireless.1.scan_list.status=enabled
    wireless.1.security.type=none
    wireless.1.sens=0
    wireless.1.signal_led1=94
    wireless.1.signal_led2=80
    wireless.1.signal_led3=73
    wireless.1.signal_led4=65
    wireless.1.signal_led_status=enabled
    wireless.1.ssid=  tecnet 1O charles1  
    wireless.1.status=enabled
    wireless.1.wds.1.peer=
    wireless.1.wds.2.peer=
    wireless.1.wds.3.peer=
    wireless.1.wds.4.peer=
    wireless.1.wds.5.peer=
    wireless.1.wds.6.peer=
    wireless.1.wds.status=enabled
    wireless.1.wmm=enabled
    wireless.1.wmmlevel=
    wireless.status=enabled
    wpasupplicant.device.1.status=disabled
    wpasupplicant.profile.1.network.1.psk= kwqrt67843loanh3251O
    wpasupplicant.status=disabled

  • Rogerio Outubro 21, 2012 10:50

    Todas so nao sei  se vai funcionar com os dois ultimos firmeware.

  • Orlando Barbosa da Silva Outubro 21, 2012 10:18

    mais isso server para toda linha ubnt

This reply was deleted.